Thursday, June 16, 2016

Gelli® Printed Diamond Kite

Hi there! My name is Marsha Valk and I’m excited to share this simple diamond kite! It is easy to make, fun to create and also loads of fun to play with once it’s done!



Preparations:
First decide on how tall you want your kite to be. This determines the length of the dowels you’ll need and also the measurements of the paper needed to create the sail.

For a diamond kite you need two wooden dowels with a fixed size ratio of 3:2. The kite paper I used happened to be a little over 27.5” tall, so I used a small hand saw to trim my long dowel to 27.5” and then my short dowel automatically had to have a length of 18.33”.

Cut a little notch in each end of the dowels. This is where the string will be attached later on.


I trimmed my paper sheet down to slightly larger than 27.5” x 18.33”. Kite paper is a translucent glossy lightweight paper and you can easily substitute it with deli paper or even something like newspaper.

Mark makers and printing plates:
I wanted the kite to have stars and stripes. So I went to look for mark making tools that could make stripes or stars.

The stripes were easy enough: stripped corrugated cardboard, a handmade foam stamp and the  Gelli® Arts Square Edge Tools would do the trick. I also created a broad striped printing plate by adhering a couple of craft sticks to a piece of cardboard.


The stars were a bit harder to find, so I created my own stamps by drawing simple stars on thick craft foam and then cutting them out with scissors. The stencil was made by drawing stars on a transparency and then cutting the insides out with scissors. I found the stars roller stamp at a local store (HEMA), but you can easily make something similar yourself. The sequins will act as a mask.


Printing:
Apply acrylic paint to the Gelli® plate of your choice. I used the 5" x 5Student Plate.

Make marks with the stars and stripes tools. You’ll only need a thin layer of paint for each print. Too much paint will buckle the paper. Be sure to clean the plate and the brayer when you switch to another paint color.

Watch my video to get a better idea of how I did it! 

Because of the translucent nature of the paper, it’s easy to see where you print and there is no need to turn the entire sheet over after each print. You can stamp off your stamps and stencils on the backside of the paper. These images will shine through to the front of the paper when it’s done!


Once you’ve got the whole paper covered, you can add some stenciling or more stamped images on top.

Assemble the kite:
Tape the two wooden dowels together with strips of duct tape, as tight as possible. The short dowel should be placed at exactly 1/3 of the long dowel (in my case at 9.2” from the top).


Run the string along the notches in the dowels. Start at the bottom and end with a little knot.



Reinforce the knot with tape if necessary. Place the kite frame on top of the paper. Cut the sail slightly larger than the kite frame. Add glue to the seam and fold it over.



Attach a flying line to the kite and add a tale made of ribbon, fabric or paper strips. Or add a length of string with paper or fabric bows every 16”.






The kite is ready to fly! Go outside and find out if it will sail!Not into diamond kites? Or do you want to make a different kind of kite? No problem! You can use Gelli® printed kite paper with any type of kite building method you want!





Materials

Gelli® Arts:

Other:
Transparent paper (Folia) or deli paper
Acrylic paint (Galeria)
Wooden dowel or bamboo sticks 1/4” wide
Hand saw
Transparency
Craft foam
Cardboard
Star shaped sequins
Star stamp roller (HEMA)
Craft sticks
Scissors
Ruler
Glue stick (Pritt)
Cosmetic sponge
Duct tape
String

PS: Please—share your prints with us on our Facebook page, or on Instagram using the hashtag #gelliprint #gelliarts and #gelliplate. Tag us with @gelliarts on Instagram and Twitter too! We love to see what you're creating!!

Remember, we now have Gelli partners all over the world, so it's easier than ever to find a Gelli retailer near you!

     




SaveSave

9 comments:

  1. This is totally awesome!! I might have to try to make one for each of my grandchildren! They would love them! Thanks for the inspiration!

    ReplyDelete
    Replies
    1. Thank you Barb! Glad you enjoyed it!

      Delete
  2. That is a wonderful idea and something to do with my GS next time he's over. We used to make kites like this using wallpaper when I was a child with a lovely long tail. They didn't last long, but between making them and getting them to fly we had hours of fun.

    ReplyDelete
    Replies
    1. Thank you, Margaret! Yes, you're probably right about the durability, but... you can always create a new one :-).

      Delete
  3. Such a lovely project!

    Xx Michelle

    ReplyDelete
    Replies
    1. Thank you Michelle! So glad you like it!

      Delete
  4. Art is an basic activity for human being. It provides a lot of joy and a happiness. The IT art is an impressive and informative blog for all.

    ReplyDelete

Thanks so much for taking the time to comment on our blog! We hope you find it fun and helpful in your artistic endeavors!

We will try my best to answer your questions and provide good, helpful information in a timely manner.

We look forward to hearing from you and thank you for stopping by!
Happy Printing!
Gelli Arts®

You might also like:

Related Posts Plugin for WordPress, Blogger...